Welcome to the official website of Dongguan Minz Rubber & Plastics Co., Ltd.

中文简体  | English

Dongguan Mingzhen Rubber & Plastic Products Co., Ltd.

18 yearsFocus on R & D and production of silicone rubber products

Become a respected supplier of silicone rubber products

Service Hotline:

+86-136 6988 8704

Dongguan Minz Rubber & Plastics Co., Ltd.

Add.: No.4, New Industrial Road, Shipai Tangwei, shipai town, Dongguan City
Tel: +86-0769-8665 2688
Fax: +86-796-8180 6477
Contact: Miss Li +86-136 6988 8704
Mailbox:lixiaoxia@dgminz.com.cn

Silicone products to remove static electricity is very effective four methods

Release time:

2019-05-17 12:30

Source:

Silicone products to remove static electricity is very effective four methods
 
Silicone ProductsHow to eliminate static electricity Method 1: When it comes to the word static electricity, everyone must have deep feelings, especially in winter, the static electricity of human body is quite obvious, and many silicone products also have static electricity. If a silicone product factory does not take anti-static measures well, the accumulation of static electricity on silicone products will also cause fire!
 
Mingzhen Silicone Products Factory will introduce how to better eliminate static electricity on silica gel products:
 
First of all, we start from the source, that is, on the silica gel raw materials (foaming raw materials and materials are also used), adding antistatic agents to the raw materials can effectively control the generation of static electricity. During production, static elimination equipment can be installed at the silica gel raw material inlet of the silica gel injection molding machine, and preventing air humidifiers in the workshop can also prevent the generation of static electricity in silica gel products! When static electricity is generated, we can use static eliminator, ion wind stick and other tools to eliminate static electricity on silica gel products. These static elimination equipment can produce a large number of positive and negative ions to eliminate static electricity!
 
We can also spray static prevention agent on the finished silicone products, which can also prevent static electricity without damaging the silicone products! I believe that as long as we strictly control the production quality of silicone products, in addition to the static electricity generated by silicone, we as a silicone product manufacturer have a responsibility that cannot be slackened. Only when this writing problem is solved can the quality and grade of silicone products be greatly improved and the credibility of customers to manufacturers be effectively enhanced!
 
Silica gel products to remove static electricity method 2: ion wind bar, static eliminator its strong ion wind to remove static electricity and foreign matter, dust on the surface of the object, belongs to the industrial category suitable for the initial electrostatic dust removal of flat objects.
 
In the high-speed plastic forming machine, slitting machine, stretching machine and other plastic machinery and equipment to install rod static elimination equipment, can effectively eliminate the plastic sheet high-speed pull generated when high-voltage static electricity, to prevent the sheet due to electrostatic adsorption of dust in the air or between the sheet due to static electricity and mutual adhesion, effectively improve the production and processing of plastic sheet product grade, quality. The ring-type static elimination equipment is installed at the entrance of the plastic raw material of the silicone injection molding machine, which can eliminate the high-voltage static electricity generated in the flow of the raw material, so as to prevent the raw material from being clumped and piled up at the entrance due to static electricity, which directly affects the production.
Of course, you can also add antistatic agents in the plastic, production workshop humidification is a good method. Can also be used to prevent static electricity, spray on the surface of the product without destroying the performance and transparency of the product at the same time to achieve permanent antistatic. Anti-static liquid can be added when compounding, so that it is coated on the inner and outer layers, and the liquid is similar to alcohol!
 
How to eliminate static electricity in silica gel products, how to eliminate static electricity in silica gel products, how to eliminate static electricity in silica gel products, method 3: electronic products should be tested for electrostatic immunity before leaving the factory, and well-known manufacturers like apple should consider the design of electrostatic protection, so under normal conditions, qualified electronic products will not be damaged by static electricity in life, so under normal circumstances, silicone sleeve is not easy to damage your ipad.
 
If the static electricity generated by the silicone sleeve is too large, so that you are worried about its safety, the more professional method is to replace the anti-static protective sleeve, or in the silicone sleeve coated with anti-static liquid, if you do not have these conditions, you can consider adding some metal accessories on the silicone sleeve, through the form of tip discharge to release the accumulated charge on the silicone sleeve, or in the case of not affecting the appearance of the download silicone sleeve on some conductive or antistatic tape can reduce the insulation of the silicone surface.
 
How to eliminate static electricity in silica gel products, how to remove static electricity in silica gel products, how to remove static electricity in silica gel products, method 4: Mingzhen Silicone Products Co., Ltd. tells you to start from the source, that is, to start on the raw materials of silica gel products, adding antistatic agent to the raw materials, which can effectively control the generation of static electricity. During production, static elimination equipment can be installed at the raw material inlet of silica gel injection molding machine, preventing air humidifiers in the workshop can also prevent the generation of static electricity in silica gel products!
 
When static electricity is generated, tools such as static eliminator, ion wind stick or FFU can be used to eliminate static electricity on silica gel products. These static elimination devices can generate a large number of positive and negative ions to eliminate static electricity! We can also spray static prevention agent on the finished silicone products, which can also prevent static electricity without damaging the silicone products! The elimination of static electricity in silicone products greatly improves the quality and grade of silicone products, and effectively enhances the credibility of customers to manufacturers.

Previous Page

The reason why the surface of silicone products is not smooth_what causes the surface of silicone products to be not smooth

Food Grade Silicone Benefits for Baby Products Mobile Phone Waterproof Artifact: Liquid Silicone

Next Page

Previous Page

The reason why the surface of silicone products is not smooth_what causes the surface of silicone products to be not smooth

Next Page

Food Grade Silicone Benefits for Baby Products Mobile Phone Waterproof Artifact: Liquid Silicone

More information

What is the difference between silicone plug and rubber plug

Silicone plug and rubber plug which one effect is good? Then today we will popularize their difference to where the end point is. First of all, rubber plug products, as a common type of industrial products and accessories, or have strong advantages, such as dust and water resistance, wear resistance, tear resistance, aging resistance, oil seal resistance and ozone radiation resistance, etc., while rubber materials are divided into various types, and the side materials over there can be made of dozens of compound materials, so different attribute functions can be deployed for different needs, as for some industries such as mechanical tight closure, electronic tight closure, vehicle construction and even aerospace and military industry, rubber blocking is the most suitable. Silicone rubber plug and rubber plug have one thing in common. They can be molded in the molding vulcanizer of silicone product manufacturers. The difference is that they are more environmentally friendly, have good high and low temperature resistance, feel better when touching by color hands, and can be in contact with human body skin for a long time. Therefore, silicone plugs for earphones and medical grade silicone plugs are widely used even in food silicone appliances, mainly or because of the material in particular the nature of the achievements of its scope of application. Silicone plug is different. Its material is mainly based on environmental protection advantages, material texture and comfortable application. Therefore, it is used in some electronic products, survival products and small-scale waterproof and dustproof household appliances. Its raw materials are mixed by precipitation method silica gel, high-fine molecular silicone gum and white carbon black. The molecular chain of the product is called heart, soft and comfortable to use! Compared with the materials of silica gel and rubber, they can be compared as follows: new technologies are used in traditional industries. Rubber materials have been heard for a long time in early years, so the comparison of rubber materials accounts for the majority. Up to now, more and more silicone rubber products have been reused because they can replace larger usage compared with rubber, namely environmental protection performance and various technologies, such as shape, pattern and color, etc. www.mingzhen2006.com

What are the fields of application of silicone keys for equipment

Characteristics and uses of silica gel Silicone is a kind of rubber. The vulcanized silicone rubber has heat resistance, cold resistance, ozone resistance, atmospheric aging resistance and good electrical insulation properties. The disadvantage of silicone rubber is that the tensile strength and elongation at break are small, and the compression deformation is large. Suitable for making parts used in high temperature, low temperature, sunlight, atmosphere, ozone environment and electrical insulation parts. Dimensional accuracy and recommend marking tolerance Trajectory material is an elastomer, compared to the plastic material, the direct impact of the shrinkage rate of many and complex factors, precision than plastic parts more difficult to do accurate, in the specific design should be fully considered, there should be no high precision. If the basic size is too large to meet the dimensional accuracy required by the design, it can be solved by the method of deformation of the positioning column with the substrate. Where dimensional accuracy is required, there must be room for convenient mold repair in the design. Etched text and patterns Silicone substrate can be designed out of the trademark pattern and text, in the molding products at the same time molding out. The group and text on the products are convex and concave two types, considering the convenience of mold processing, are generally designed as convex. In order to facilitate the replacement of marks or models, the marked parts can be designed as inserts during mold design. When the product model changes, only the marked parts in the mold cavity can be replaced to meet the needs of mark replacement. As part of this type of article, it should be designed to allow the presence of flash debris at the contour of the insert tile at the marked location. For conductive rubber, the stroke is generally 0.8~1.5mm; the exhaust groove (I. e. gas pit) is designed to prevent adsorption between the PCB and the key action. For tact switches, the stroke depends on the stroke of the switch itself (and the stroke for preventing misoperation), as described later. If the substrate is not bonded to the PCB board, the structural element of the air slot can be omitted. The key design has a hand feeling problem. Different graphs correspond to different hand feelings. According to experience, when (FP-FC)/FP is 40%-60%, the hand feeling is better. Key Typical Structure and Application According to the specific occasions where the keys are used, as well as the specific requirements of the product for the service life, pressing force, and hand feeling of the keys, the structure and application of the keys are shown in the following figure. The life of the silicone key is directly related to the material and the inclined wall structure, and is determined according to the design requirements. Part of the product silicone key life reference: Remote controller: 500000 times; Telephone type: 1 million times; Laptop computers: 4 million to 5 million times; Computer keyboard: 500~10 million; The life of silicone keys for monitoring products is defined as more than 500000 times; The ordinary life of B super silicone keys is defined as more than 1 million times,

The convenience of the use of industrial silicone buttons

In order to solve the above problems and technical defects, after continuous updating and design, a multi-station silicone button trimming machine was invented, and a utility model patent was applied. The utility model relates to a multi-position silicone button trimming machine, which comprises a base, a gantry frame and four cutting cylinders, and the four cutting cylinders are arranged vertically on the top of the gantry frame in a horizontal straight line. The beneficial effect achieved by the utility model is that the structure design is reasonable. By adopting the combination design of four reinforcement tables and four cutting blades on the gantry, the device can simultaneously trim four silicone button products. Thereby greatly improving the efficiency of trimming processing of silicone products. With the continuous expansion of the silicone button market, how to improve the processing efficiency of the silicone button has made producers pay more and more attention. The trimming of the silicone button is an important step in the production process of the silicone button, and the trimming of the traditional silicone button The processing efficiency cannot be improved, which affects the overall production efficiency of the silicone button. Various types of silica gel have different microporous structures due to their different manufacturing methods. The chemical composition and physical structure of silica gel determine that it has many characteristics that are difficult to replace other similar materials: high adsorption performance, good thermal stability, stable chemical properties, and high mechanical strength. Silica gel according to its pore size is divided into: macroporous silica gel, coarse pore silica gel, type B silica gel, fine pore silica gel. www.mingzhen2006.com

What are the molding techniques of rubber products?

Calendering: suitable for the manufacture of simple sheet, plate products. It is a method of pressing the mixture into a film through a calender called calendering. Some rubber products (such as tires, tape, hose, etc.) used in textile fiber materials, coated with a thin layer of glue, glue coating process is generally completed on the calender. The fiber material needs to be dried and dipped before calendering. The purpose of drying is to reduce the moisture content of the fiber material (so as to avoid water evaporation and foaming) and increase the temperature of the fiber material to ensure the quality of the calendering process. Dipper is the process before hanging glue, the purpose is to improve the binding performance of fiber materials and glue. Extrusion molding: Used for more complex rubber products, such as tire treads, rubber tubes, and metal wire surface coatings, which need to be manufactured by extrusion molding. The plastic mixture was placed into the hopper of the extruder. Under the extrusion of the screw, a method of continuous molding through a variety of mouth before pressing out, the rubber material is preheated to make the rubber material soft and easy to extrude, so as to obtain rubber products with smooth surface and accurate size. The rubber industry is one of the important basic industries of the national economy. It not only provides people with light industrial rubber products that are indispensable in daily life, but also provides various rubber production equipment or rubber parts for heavy and emerging industries (such as mining, transportation, construction, machinery and electronic products). It can be seen that there are many kinds of products in the rubber industry, and the backward industry is very extensive. Molding molding: can also be used to manufacture some complex shapes (such as cups, seals) of rubber products, with the help of the molding of the female and male molds, the rubber material is placed in the mold and heated. www.mingzhen2006.com

How to print the pattern on the transparent key

Some laser marking machines have played opaque keys. While using laser typing to knock out the paint, they will also burn the plastic parts that can transmit light, but cannot transmit light! Changzhou laser marking machine has a special device, which can adjust the machine to the function of laser processing light-transmitting key. The laser can clean the paint sprayed on the surface very clean without burning light-transmitting plastic, thus realizing light-transmitting key laser processing! YAG laser marking machine, the general laser marking machine can not do through the key! Light transmission keys, also called light transmission buttons, are widely used in electronic products. In dark environments, they can accurately and accurately find each button. The light transmission keys include a light transmission key body, an electronic switch located below the key body, and a luminous body. The luminous body is arranged on the lower side of the key body. A light guide body is arranged below the key body, and the light guide body has a body, the upper side of the body extends an extension to the position where the electronic switch is located, the outer surface of the extension is a first reflective slope, the lower surface of the body is a second reflective slope and doubles as a light touch surface that can be contacted with the electronic switch, and a light input part connected with the extension part and arranged corresponding to the light emitting body, the light emitting body emits light, the light is emitted to the first reflective slope through the introduction portion, and is reflected by the first reflective slope into the body, and the light entering the body is reflected by the second reflective slope out of the key body. The structure makes the light emitted from the light emitting surface of the key body more uniform, the key is more beautiful, and the user can accurately find the corresponding function key. The pattern and text on the keys are processed by laser typing! In our life, there are many keys and buttons that use laser typing and can transmit light, such as mobile phone keys, car audio keys, computer keys, and various electronic and electrical keys! www.mingzhen2006.com