Welcome to the official website of Dongguan Minz Rubber & Plastics Co., Ltd.

中文简体  | English

Dongguan Mingzhen Rubber & Plastic Products Co., Ltd.

18 yearsFocus on R & D and production of silicone rubber products

Become a respected supplier of silicone rubber products

Service Hotline:

+86-136 6988 8704

Dongguan Minz Rubber & Plastics Co., Ltd.

Add.: No.4, New Industrial Road, Shipai Tangwei, shipai town, Dongguan City
Tel: +86-0769-8665 2688
Fax: +86-796-8180 6477
Contact: Miss Li +86-136 6988 8704
Mailbox:lixiaoxia@dgminz.com.cn

Silicone products: application in the field of electronic components

Release time:

2019-06-14 12:30

Source:

Silicone ProductsApplication in the field of electronic components
 
 
Silicone products: application in the field of electronic components, monocrystalline silicon is a relatively active non-metallic element, is an important part of crystal materials, in the forefront of the development of new materials. Monocrystalline silicon is mainly used in the production of semiconductor components, is the raw material for the manufacture of semiconductor silicon devices, used to make high-power rectifiers, high-power transistors, diodes, switching devices, etc. Its follow-up products integrated circuits and semiconductor separation devices have been widely used in various fields, and also occupy an important position in military electronic equipment.
 
Silicon is a semiconductor material, and its own conductivity is not very good. However, its resistivity can be precisely controlled by adding appropriate dopants. Before manufacturing a semiconductor, the silicon must be converted into a wafer. This begins with the growth of a silicon ingot. Monocrystalline silicon is a solid in which atoms are periodically formed in a three-dimensional spatial pattern throughout the material.
 
Polysilicon gasket is a lot of small single crystal with different crystal to form alone, can not be used to make semiconductor circuits. Polysilicon must be melted into a single crystal before it can be processed into wafers used in semiconductor applications. Processing silicon wafers to produce an ingot can take from one week to one month, depending on many factors, including size, quality, and end-user requirements. More than 75% of single crystal silicon wafers are grown by the Czochralski method (CZ, also known as the Czochralski method).
Polycrystalline silicon is a form of elemental silicon. When the molten elemental silicon is solidified under the condition of supercooling, the silicon atoms are arranged into many crystal nuclei in the form of diamond lattice. If these crystal nuclei grow into grains with different crystal plane orientations, these grains will combine to crystallize into polysilicon.
 
 
Monocrystalline silicon gasket is a kind of active non-metallic element, which is an important part of crystal materials and is at the forefront of the development of new materials. Monocrystalline silicon is mainly used in the production of semiconductor components, is the raw material for the manufacture of semiconductor silicon devices, used to make high-power rectifiers, high-power transistors, diodes, switching devices, etc. Its follow-up products integrated circuits and semiconductor separation devices have been widely used in various fields, and also occupy an important position in military electronic equipment.

Previous Page

What is a car oil seal?

What kind of seals are oil seals and dust seals?

Next Page

Previous Page

What is a car oil seal?

Next Page

What kind of seals are oil seals and dust seals?

More information

What is the difference between silicone plug and rubber plug

Silicone plug and rubber plug which one effect is good? Then today we will popularize their difference to where the end point is. First of all, rubber plug products, as a common type of industrial products and accessories, or have strong advantages, such as dust and water resistance, wear resistance, tear resistance, aging resistance, oil seal resistance and ozone radiation resistance, etc., while rubber materials are divided into various types, and the side materials over there can be made of dozens of compound materials, so different attribute functions can be deployed for different needs, as for some industries such as mechanical tight closure, electronic tight closure, vehicle construction and even aerospace and military industry, rubber blocking is the most suitable. Silicone rubber plug and rubber plug have one thing in common. They can be molded in the molding vulcanizer of silicone product manufacturers. The difference is that they are more environmentally friendly, have good high and low temperature resistance, feel better when touching by color hands, and can be in contact with human body skin for a long time. Therefore, silicone plugs for earphones and medical grade silicone plugs are widely used even in food silicone appliances, mainly or because of the material in particular the nature of the achievements of its scope of application. Silicone plug is different. Its material is mainly based on environmental protection advantages, material texture and comfortable application. Therefore, it is used in some electronic products, survival products and small-scale waterproof and dustproof household appliances. Its raw materials are mixed by precipitation method silica gel, high-fine molecular silicone gum and white carbon black. The molecular chain of the product is called heart, soft and comfortable to use! Compared with the materials of silica gel and rubber, they can be compared as follows: new technologies are used in traditional industries. Rubber materials have been heard for a long time in early years, so the comparison of rubber materials accounts for the majority. Up to now, more and more silicone rubber products have been reused because they can replace larger usage compared with rubber, namely environmental protection performance and various technologies, such as shape, pattern and color, etc. www.mingzhen2006.com

What are the fields of application of silicone keys for equipment

Characteristics and uses of silica gel Silicone is a kind of rubber. The vulcanized silicone rubber has heat resistance, cold resistance, ozone resistance, atmospheric aging resistance and good electrical insulation properties. The disadvantage of silicone rubber is that the tensile strength and elongation at break are small, and the compression deformation is large. Suitable for making parts used in high temperature, low temperature, sunlight, atmosphere, ozone environment and electrical insulation parts. Dimensional accuracy and recommend marking tolerance Trajectory material is an elastomer, compared to the plastic material, the direct impact of the shrinkage rate of many and complex factors, precision than plastic parts more difficult to do accurate, in the specific design should be fully considered, there should be no high precision. If the basic size is too large to meet the dimensional accuracy required by the design, it can be solved by the method of deformation of the positioning column with the substrate. Where dimensional accuracy is required, there must be room for convenient mold repair in the design. Etched text and patterns Silicone substrate can be designed out of the trademark pattern and text, in the molding products at the same time molding out. The group and text on the products are convex and concave two types, considering the convenience of mold processing, are generally designed as convex. In order to facilitate the replacement of marks or models, the marked parts can be designed as inserts during mold design. When the product model changes, only the marked parts in the mold cavity can be replaced to meet the needs of mark replacement. As part of this type of article, it should be designed to allow the presence of flash debris at the contour of the insert tile at the marked location. For conductive rubber, the stroke is generally 0.8~1.5mm; the exhaust groove (I. e. gas pit) is designed to prevent adsorption between the PCB and the key action. For tact switches, the stroke depends on the stroke of the switch itself (and the stroke for preventing misoperation), as described later. If the substrate is not bonded to the PCB board, the structural element of the air slot can be omitted. The key design has a hand feeling problem. Different graphs correspond to different hand feelings. According to experience, when (FP-FC)/FP is 40%-60%, the hand feeling is better. Key Typical Structure and Application According to the specific occasions where the keys are used, as well as the specific requirements of the product for the service life, pressing force, and hand feeling of the keys, the structure and application of the keys are shown in the following figure. The life of the silicone key is directly related to the material and the inclined wall structure, and is determined according to the design requirements. Part of the product silicone key life reference: Remote controller: 500000 times; Telephone type: 1 million times; Laptop computers: 4 million to 5 million times; Computer keyboard: 500~10 million; The life of silicone keys for monitoring products is defined as more than 500000 times; The ordinary life of B super silicone keys is defined as more than 1 million times,

The convenience of the use of industrial silicone buttons

In order to solve the above problems and technical defects, after continuous updating and design, a multi-station silicone button trimming machine was invented, and a utility model patent was applied. The utility model relates to a multi-position silicone button trimming machine, which comprises a base, a gantry frame and four cutting cylinders, and the four cutting cylinders are arranged vertically on the top of the gantry frame in a horizontal straight line. The beneficial effect achieved by the utility model is that the structure design is reasonable. By adopting the combination design of four reinforcement tables and four cutting blades on the gantry, the device can simultaneously trim four silicone button products. Thereby greatly improving the efficiency of trimming processing of silicone products. With the continuous expansion of the silicone button market, how to improve the processing efficiency of the silicone button has made producers pay more and more attention. The trimming of the silicone button is an important step in the production process of the silicone button, and the trimming of the traditional silicone button The processing efficiency cannot be improved, which affects the overall production efficiency of the silicone button. Various types of silica gel have different microporous structures due to their different manufacturing methods. The chemical composition and physical structure of silica gel determine that it has many characteristics that are difficult to replace other similar materials: high adsorption performance, good thermal stability, stable chemical properties, and high mechanical strength. Silica gel according to its pore size is divided into: macroporous silica gel, coarse pore silica gel, type B silica gel, fine pore silica gel. www.mingzhen2006.com

What are the molding techniques of rubber products?

Calendering: suitable for the manufacture of simple sheet, plate products. It is a method of pressing the mixture into a film through a calender called calendering. Some rubber products (such as tires, tape, hose, etc.) used in textile fiber materials, coated with a thin layer of glue, glue coating process is generally completed on the calender. The fiber material needs to be dried and dipped before calendering. The purpose of drying is to reduce the moisture content of the fiber material (so as to avoid water evaporation and foaming) and increase the temperature of the fiber material to ensure the quality of the calendering process. Dipper is the process before hanging glue, the purpose is to improve the binding performance of fiber materials and glue. Extrusion molding: Used for more complex rubber products, such as tire treads, rubber tubes, and metal wire surface coatings, which need to be manufactured by extrusion molding. The plastic mixture was placed into the hopper of the extruder. Under the extrusion of the screw, a method of continuous molding through a variety of mouth before pressing out, the rubber material is preheated to make the rubber material soft and easy to extrude, so as to obtain rubber products with smooth surface and accurate size. The rubber industry is one of the important basic industries of the national economy. It not only provides people with light industrial rubber products that are indispensable in daily life, but also provides various rubber production equipment or rubber parts for heavy and emerging industries (such as mining, transportation, construction, machinery and electronic products). It can be seen that there are many kinds of products in the rubber industry, and the backward industry is very extensive. Molding molding: can also be used to manufacture some complex shapes (such as cups, seals) of rubber products, with the help of the molding of the female and male molds, the rubber material is placed in the mold and heated. www.mingzhen2006.com

How to print the pattern on the transparent key

Some laser marking machines have played opaque keys. While using laser typing to knock out the paint, they will also burn the plastic parts that can transmit light, but cannot transmit light! Changzhou laser marking machine has a special device, which can adjust the machine to the function of laser processing light-transmitting key. The laser can clean the paint sprayed on the surface very clean without burning light-transmitting plastic, thus realizing light-transmitting key laser processing! YAG laser marking machine, the general laser marking machine can not do through the key! Light transmission keys, also called light transmission buttons, are widely used in electronic products. In dark environments, they can accurately and accurately find each button. The light transmission keys include a light transmission key body, an electronic switch located below the key body, and a luminous body. The luminous body is arranged on the lower side of the key body. A light guide body is arranged below the key body, and the light guide body has a body, the upper side of the body extends an extension to the position where the electronic switch is located, the outer surface of the extension is a first reflective slope, the lower surface of the body is a second reflective slope and doubles as a light touch surface that can be contacted with the electronic switch, and a light input part connected with the extension part and arranged corresponding to the light emitting body, the light emitting body emits light, the light is emitted to the first reflective slope through the introduction portion, and is reflected by the first reflective slope into the body, and the light entering the body is reflected by the second reflective slope out of the key body. The structure makes the light emitted from the light emitting surface of the key body more uniform, the key is more beautiful, and the user can accurately find the corresponding function key. The pattern and text on the keys are processed by laser typing! In our life, there are many keys and buttons that use laser typing and can transmit light, such as mobile phone keys, car audio keys, computer keys, and various electronic and electrical keys! www.mingzhen2006.com